PDA

View Full Version : Simple brick or block wall


vader9900
12-13-2008, 08:11 AM
This is a how-to on building a simple but effective block or brick wall as seen HERE. (http://www.joedios.com/dioramas/showimage.php?i=18240&c=7)
I am going to build a small sample wall here for reference, the one I used in my picture is 16" wide & 12" tall. The wall is simply foam core, I use the black type because it takes paint better than the white. It is easy to find, available at WalMart. The first thing you want to do is sand the side you are going to be working on. This will give you a little texture to your blocks.

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3693.jpg

Next we are going to draw out our blocks. I know some of you are artist and can do this freehand, I am not, so I use a pencil & a ruler. First the rows:

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3694.jpg

I am going to make 1" x 1/2" blocks, so the rows are marked every 1/2" down the foam core. I then mark each block at 1" intervals across alternating every other row by 1/2" to offset your blocks

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3695.jpg

Every other row offset by 1/2

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3696.jpg

vader9900
12-13-2008, 08:26 AM
After you have your blocks drawn out, its time to emboss the blocks into the foam core. I used a wooden stylus, it is for sculpting with clay, I think I got it at Michaels. Any tool with a blunt tip will work.

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3698.jpg

You don't want the tool to be sharp because you do not want to puncture the outer paper of the foam core (notice I did in the bottom left corner below). A ball point pen will work well too. Take your stylus and rub back and forth over your lines to make a indentation in the paper of the foam core. Make it as deep as you can without puncturing the paper.

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3699.jpg

Then round all the corners of your bricks

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3701.jpg

Add some character - put as much or as little detail into it as you like.

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3702.jpg

vader9900
12-13-2008, 08:32 AM
Time to paint. First coat will be a heavy drybrush. I use all Testors acrylic paints. The base is Battle Ship Grey, but any dark grey will work.

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3703.jpg

Foam core will warp when it gets wet and allowed to air dry, acrylic paints are water based. I use a heat gun (a hair dryer will work too). It speeds up the drying time & it prevents warping. Next layer is a heavy black wash (25% black paint to 75% water)

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3704.jpg

Make sure your wash gets down in your embossed cracks & crevases. Again use your heat gun. Make sure the wash is completely dry before proceeding. Then a light drybrush of olive drab.

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3705.jpg

Then a very light drybrush of light grey

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3706.jpg

Thin out your black wash by 50% and give it another light coat, there again getting it in all the cracks. I sprayed mine down with Testors Dull Coat to seal the paint and to minimize reflection. Add figures & photograph!

http://i23.photobucket.com/albums/b367/vader9900/block%20wall/IMG_3708.jpg

Hope this helps! It actually took more time to write up this how-to than it did to make the wall. Dave

Sgt_DP
12-13-2008, 10:47 AM
That is very cool and simple to do. Thanks for the "How to". That looks great. To think how much I spent on some coble stone and other bricks that looked no where near as good as this...

Tracker
12-13-2008, 03:15 PM
That is very effective yet simple. Thanks

Rambo
12-13-2008, 09:17 PM
You're an artist. PERIOD.

vespapilot79
12-14-2008, 08:31 PM
Great work!!Well worth the time to get an awesome result as yours!!

Jaybird
12-15-2008, 12:15 PM
Thanks for the great instructions. I'm definitely going to have to try this!

Flatline
12-15-2008, 01:03 PM
thanks Dave ;)

4-Cobra
12-15-2008, 09:00 PM
Thank's for another great "How To",i'll be giving this a try.I've already tried out your Tree Building & Bush Building How To's,and with your help I think my Tree's came out great.I'm also building a Home Made Lighting Box from seeing the one you have,and when I get it finished i'm going to start posting Pic's.So Thank's for the Help...

Sonneilon
01-14-2009, 04:47 PM
Oh man... I just looked at this bad boy and it's not as hard as i was imagining it. I'm currently working on a medium scale, destroyed building set. it's going ok. But I was originally gonna fotoshop the background in (of destroyed buildings) but I'm gonna go a slightly different route. THanks for this. It really helps!

vader9900
01-14-2009, 05:28 PM
Your welcome, it really is very simple, just takes a little time.

Outrider
01-14-2009, 07:10 PM
I don't know how I missed this one. The genius is in the simplicity; so easy to do, yet so effective. I have to give this a try. Thanks Dave!